
Does an Unvented Cylinder Need Servicing Every Year?
An unvented hot water cylinder gives you strong, mains pressure hot water to every tap and shower, often several at once. It's a popular choice for larger Cambridge homes and family households. Because it stores hot water under pressure, though, it relies on a set of safety and control devices that need to keep working properly for the whole life of the cylinder.
That's why annual servicing matters. Here's what a service involves, the signs that something isn't right and why servicing supports both safety and reliability.
Quick Answer
Yes. Unvented cylinder manufacturers generally recommend servicing every 12 months by a competent engineer, and many make annual servicing a condition of their warranty. A service checks the safety devices that protect the cylinder, including the temperature and pressure relief valve, the expansion relief valve, the expansion vessel or air gap, the pressure reducing valve and the discharge pipework, as well as the controls and inlet strainer. Problems such as water dripping from the tundish, fluctuating pressure or hot water that isn't as hot as it should be are signs it needs attention sooner. Plumbox can carry out your unvented cylinder servicing alongside your annual boiler service.
Why does an unvented cylinder need servicing?
An unvented cylinder is connected directly to the mains water supply rather than being fed from a tank in the loft. That's what gives it strong pressure, but it also means the water inside is stored at pressure and heated. If the controls failed and nothing else stepped in, pressure and temperature could rise to unsafe levels.
To prevent that, every unvented cylinder has several layers of protection. These devices are designed to work automatically, but valves can stick, expansion vessels can lose their charge and strainers can block over time. Regular servicing makes sure each safety device is still doing its job.
Because of these safety requirements, unvented cylinders must be installed by a competent person under the Building Regulations. The same expertise applies to servicing them.
What safety devices and controls does a service check?
Exact components vary by manufacturer and model, but a service typically covers the following.
Temperature and pressure relief valve
This valve is the final safety device. If the water inside gets too hot or the pressure gets too high, it opens and releases water safely through the discharge pipe. The engineer checks that it operates correctly and isn't passing water when it shouldn't.
Expansion relief valve
Water expands as it heats up. The expansion relief valve releases pressure if expansion isn't being absorbed properly. Regular discharge from this valve usually indicates a problem elsewhere, often with the expansion vessel or air gap.
Expansion vessel or internal air gap
Most systems use an expansion vessel to absorb the extra volume of water as it heats. Some cylinders use an internal air gap instead. Over time, the air charge in a vessel can drop. When it does, the system can't absorb expansion properly and water is pushed out through the relief valve. The engineer checks and restores the charge where needed.
Pressure reducing valve and inlet strainer
The incoming mains pressure is controlled by a pressure reducing valve, often with a strainer to catch debris. A blocked strainer can reduce flow, and a faulty pressure reducing valve can let pressure rise too high. In areas with hard water, such as much of Cambridgeshire, scale and debris can make these checks particularly worthwhile.
Thermostats and cut-outs
The cylinder's thermostat controls the stored water temperature, and a separate high-limit cut-out shuts off the heat source if the thermostat fails. Both are tested during a service, along with any immersion heater.
Tundish and discharge pipework
The tundish is the open funnel on the discharge pipe that lets you see if a valve is releasing water. The engineer checks that the discharge pipework is clear, correctly routed and terminating somewhere safe.
Signs your unvented cylinder needs attention
Don't wait for the annual service if you notice any of these:
- Water dripping or running through the tundish. This means a relief valve is releasing water. Intermittent dripping often points to the expansion vessel or air gap. Continuous discharge needs checking promptly.
- Hot water from the discharge pipe. If very hot water is discharging, the manufacturer's instructions usually tell you to switch off the heat source (the boiler or immersion heater) but not to turn off the water supply, and then call a competent engineer.
- Fluctuating pressure at the taps. This can indicate a problem with the pressure reducing valve or expansion vessel.
- Water not as hot as usual. A thermostat, immersion heater or coil issue can affect temperature.
- Banging or unusual noises. This can be a sign of scale build-up or pressure problems.
- Leaks or corrosion around fittings. Any visible water or staining near the cylinder should be investigated.
What does an engineer check during a service?
A typical unvented cylinder service includes:
- Visual inspection of the cylinder, fittings and pipework for leaks or corrosion
- Testing the temperature and pressure relief valve and the expansion relief valve
- Checking and recharging the expansion vessel, or checking the air gap, where applicable
- Checking the pressure reducing valve and cleaning the inlet strainer
- Testing the thermostat, high-limit cut-out and any immersion heater
- Checking the tundish and discharge pipework
- Recording the results and advising on anything that needs repair or replacement
Many homeowners find it convenient to have the cylinder serviced at the same visit as their boiler. Our boiler service in Cambridge can be combined with an unvented cylinder service.
What do manufacturers require?
Cylinder manufacturers publish maintenance requirements in their installation and user manuals. For example, Heatrae Sadia's Megaflo Eco installation manual says maintenance checks should be carried out annually by a competent person experienced with unvented systems, and its warranty depends on regular maintenance having been carried out. It also advises extra care in very hard water areas to limit limescale. Other manufacturers set out similar conditions.
Check your cylinder's paperwork for the specific requirements. If you've lost it, the make and model are usually on a label on the cylinder, and an engineer can check the manufacturer's guidance for you.
How regular servicing supports performance and reliability
Beyond safety, a well maintained cylinder simply works better. Clean strainers and correctly set valves help maintain flow and pressure. A properly charged expansion vessel stops water being wasted through the relief valve. Working thermostats keep your hot water at the right temperature without wasting energy.
Servicing also means small problems are caught early, before a failed component leaves you without hot water. If you're still deciding whether an unvented cylinder is right for your home, our comparison of an unvented cylinder vs a combi boiler explains how the two systems differ. And if you live in a hard water area, our guide to hard water and your boiler explains why scale is worth taking seriously.
Frequently asked questions
Is an unvented cylinder service a legal requirement?
For homeowners, annual servicing is a manufacturer recommendation rather than a general legal requirement. However, installation must comply with the Building Regulations, and skipping servicing can affect your warranty. Landlords should also consider their wider responsibilities for keeping hot water systems in safe working order.
Can the boiler engineer service the cylinder at the same time?
Often, yes, as long as the engineer is competent to work on unvented systems. Combining the two in one visit is usually the most convenient option.
Why is water dripping from my tundish?
A relief valve is releasing water. Occasional dripping often means the expansion vessel has lost its charge. Continuous or hot discharge needs prompt attention from an engineer.
How long does an unvented cylinder last?
It depends on the model, water quality and how well it's maintained. Regular servicing helps components last longer and identifies parts that need replacing before they fail.
Do I need to turn anything off before a service?
No. Your engineer will isolate the cylinder and heat source as needed during the visit.
Unvented cylinder servicing in Cambridge
If your unvented cylinder hasn't been serviced in the last year, or you've noticed water at the tundish, it's worth booking a check. Plumbox installs, services and repairs unvented hot water cylinders across Cambridge and Cambridgeshire. Contact the Plumbox team or call 01223 867038 to arrange a service.

